top of page

Ford Mustang GT (2005+/GT350 (2015-2016)/ Boss 302 (2012-2013)/Cobra (1999-2004) Fuel Injector Clinic Injector Set: 8x2150cc/min (200lbs/hr) at 3 bar (43.5psi) fuel pressure. Saturated / High Impedance Ball & Seat Injectors. Includes pigtails PGTDEN8 or add Plug & Play adaptors PADPDtoU8. These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. Plug and Play Ford ECU Data available on our website. DO NOT USE WITH VP-Q16 or OTHER MTBE OXYGENATED FUELS.

 

This massive high performance injector is in a class of its own when low end throttle response and short pulse width control is required. State of the art Data Match Technology dynamic flow matching is used during the production of these injector sets due their large flow rate. This significantly improves the ECU’s ability to control these injectors in the sub 2ms pulse width area, typical of idle and part throttle conditions.

Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today. Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90 degrees F fuel temperature using CF-16B calibration fluid. CAUTION! The internal construction of this 2150cc/min injector includes a seal that has been found to swell when in contact with MTBE from oxygenated fuels like Q16 or VP Import. This swelling causes a significant reduction in flow through the injector and therefore renders it unsuitable for use with MTBE oxygenated fuels. Please be sure to follow the care instructions for these injectors since there are potential corrosion issues that may arise from prolonged disuse while exposed to alcohol based fuels (E85, etc.) Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly. Every injector is covered against failure caused by defects in original manufacture by our lifetime warranty.

This injector set is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology. Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today. Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90deg F fuel temperature using CF-16B calibration fluid. Superior short pulse width control and state of the art matching make these injectors easy to tune and provide great drivability. Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. If you are using aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly. Every injector is covered against failure caused by defects in original manufacture by our lifetime warranty.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering. This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.

 

Specifications:

 

Fitment Specifications

Bottom O-ring Outer Diameter

14mm

Cylinder Quantity

8

Height

64mm

Impedance

High-Z

Plug and Play Adaptor

PADPDtoU8

Top O-ring

14mm

Horsepower supported

Engine Aspiration

naturally aspirated

Fuel Pressure

43.5

WHP on E85 at 43psi 90%DC NA

1927.91

WHP on E85 at 43psi 90%DC Supercharged

1752.65

WHP on E85 at 43psi 90%DC Turbo

1606.59

WHP on E85 at 58psi 90%DC NA

2226.74

WHP on E85 at 58psi 90%DC Supercharged

2024.31

WHP on E85 at 58psi 90%DC Turbo

1855.62

WHP on Gas at 43psi 90%DC NA

2506.29

WHP on Gas at 43psi 90%DC Supercharged

2278.44

WHP on Gas at 43psi 90%DC Turbo

2088.57

WHP on Gas at 58psi 90%DC NA

2894.76

WHP on Gas at 58psi 90%DC Supercharged

2631.60

WHP on Gas at 58psi 90%DC Turbo

2412.30

Fuel Injector Clinic 2150cc (200 lbs/hr at 43.5 PSI fuel pressure) FIC Denso

From $1,623.00Sale Price
Quantity
    No Reviews YetShare your thoughts. Be the first to leave a review.
    Reach Out!

    *Please provide all of the information below so we may respond to your inquiry. Thank you!

    KMJ Motorsports is committed to providing high-quality performance parts and equipment. However, it's important to acknowledge that certain modifications may impact your vehicle's compliance with emissions regulations. While we strive to ensure our products meet legal standards, it's ultimately the responsibility of the vehicle owner to ensure compliance with local emissions laws and regulations. We strongly advise consulting with local authorities or regulatory bodies regarding the legality of modifications in your area. By using our products, you acknowledge and accept any potential implications on emissions compliance. Miley Industries LLC disclaims any liability for consequences arising from non-compliance with emissions laws. Thank you for your understanding and cooperation in upholding legal standards.

    © 2021 MILEY INDUSTRIES LLC

    bottom of page